电脑桌面
添加小米粒文库到电脑桌面
安装后可以在桌面快捷访问

QP-01--文件管理程序VIP免费

QP-01--文件管理程序_第1页
1/7
QP-01--文件管理程序_第2页
2/7
QP-01--文件管理程序_第3页
3/7
Shanghai Baoye Group Corp., Ltd Procedure Document上海宝冶集团有限公司程序文件Document Name:Control Procedure of Documents文件名称:文件管理程序Document No:文件编号:SBC-JZGS/ASME-010Issue for Use2024.05.16王礼本张啸风Shanghai Baoye Group Corp., Ltd上海宝冶集团有限公司Control Procedure of DocumentsSBC-JZGS/ASME-01下载后可任意编辑Revision No.版本号Reason for issue/Revision发布/修改原因Issue Date编制日期Issued by编制者Approved by批准1.1 This procedure describes the responsibility and requirements for the Quality Control Manual, design documents, technology documents, working procedure’s numbering, preparation, approval, distribution, revision and maintaining.本程序规定了 ASME 法律规范产品的质量控制手册、质量管理程序、设计文件、工艺文件的编号、编制、审批、修改发放及保存的责任和要求。2. Stipulate for numbering of QC Manual.质量控制手册编号规定2.1 Document number of QC Manual : SBC- ****-**质量控制手册的文件号:SBC-****-**Is Natural Sequence No(01、02、03···)为自然顺序号 01、02、03··· JZGS:机装分公司 Mechanical equipment installation company)2.2 The numbering of QC Manual is the same as shown in Controlled Manual Issuing List i.e. each Manual Holder has an applicable numbering manual.质量控制手册的编号和《在控手册发放表》上所示的编号相同,即每一个手册持有者有一本相应编号的手册。2.3 Document numbering of Exhibit form is listed on QC Manual, and the numbering has been marked on it.质量控制手册所列样表的表号,样表的表号已经在样表上注明。 No.*-* * 按样表页数的先后次序排列(A、B···) 序号(1、2、3、···) 样表所在手册的章节号 2.4 The preparation、 approval、 distribution and revision of the QCM should be implement as chapter1 of QC Manual.质量控制手册的编制、审批、发放、修改按质量控制手册第一章执行。3. Control of ASME Quality Control Procedure ASME 质量管理程序 Document No System of ASME Qua...

1、当您付费下载文档后,您只拥有了使用权限,并不意味着购买了版权,文档只能用于自身使用,不得用于其他商业用途(如 [转卖]进行直接盈利或[编辑后售卖]进行间接盈利)。
2、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。
3、如文档内容存在违规,或者侵犯商业秘密、侵犯著作权等,请点击“违规举报”。

碎片内容

QP-01--文件管理程序

确认删除?
VIP
微信客服
  • 扫码咨询
会员Q群
  • 会员专属群点击这里加入QQ群
客服邮箱
回到顶部