炼钢分厂工艺技术文件VIP免费

一炼分厂工艺技术文件---------------------------------------------------------------------------------------发布日期：2007.10.08实施日期：2007.10.08目录————————————————————————————————————————————————————————————————————————————XFGY01/01~11－2007（第1次修订）编制人：审核人批准人：受控状态：分发号：●基本工艺技术规程一、原料基本规程（XFGY01/01－2007)············································································1二、转炉工艺技术规程（XFGY01/02－2007)····································································5三、吹氩工艺技术规程（XFGY01/03－2007)··································································12四、LF-70t钢包精炼炉工艺技术规程（XFGY01/04－2007)·········································13五、VD-70t钢包精炼炉工艺技术规程（XFGY01/05－2007)··········································16六、1＃连铸机工艺技术规程（XFGY01/06－2007)···························································19七、2＃连铸机工艺技术规程（XFGY01/07－2007)···························································32八、结晶器电磁搅拌操作规程（XFGY01/08－2007)······················································39九、结晶器液面自动控制操规程（XFGY01/09－2007)··················································42十、放射源安全操作规程（XFGY01/10－2007)······························································43●钢种工艺技术规程十一、常炼钢种工艺操作要点（XFGY01/11－2007)······················································44附录：过程质量工艺监控规范···························································································110一、原料基本规程(XFGY01/01－2007)1、铁水供应1.1炼钢用铁水化学成分执行标准：YB/T5296-2006《炼钢用生铁》。表－1炼钢铁水技术条件参考表：牌号L04L08L10化学成分％硅[Si]≤0.45>0.45~0.85>0.85~1.25碳[C]≥3.50锰[Mn]一组≤0.40二组>0.40~1.00三组>1.00~2.00磷[P]特级≤0.100一级>0.100~0.150二级>0.150~0.250三级>0.250~0.400硫[S]特类≤0.020一类>0.020~0.030二类>0.030~0.050三类>0.050~0.070铁水温度≥1280℃带渣量≤1％注：①正常情况下转炉炼钢用铁水应符合以上要求，考虑转炉炼钢对铁水的适用情况，以上条件可暂不作为验收依据；但当铁水硅(%)>0.85、锰（％）>1.00、磷（％）>0.100、硫（％）>0.070，铁水温度(℃)<1280，应及时通知铁厂高炉，以便作出调整。③优先使用L04、L08牌号铁水，锰含量三组、磷含量二级以下、硫含量出格铁水应尽量少用。1.2当铁水罐到炉前时，应查明铁水罐号和对应（高炉）炉号，确认该罐号铁水成份已传送至转炉主控室；并按要求做好铁水成分记录；1.3兑铁前，具备条件时应测量铁水温度，并做好铁水温度记录。1.4兑铁前称量铁水重量，做好铁水装入量记录。2、废钢和生铁块供应2.1废钢执行标准...