25t-200t汽车吊性能表VIP专享VIP免费

20吨汽车吊机额定性能表以下工况仅供参考，实际请与本公司业务员联系！回转半径（m）主臂长度（m）主臂+付臂10.212.5814.9717.3519.7322.1224.524.5+7.53.020——————————————3.517.215.9————————————4.014.614.612.6——————————4.512.7512.711.710.5————————5.011.611.311.39.7————————5.510.4510109.18.1——————6.09.3998.57.66.9————7.07.247.37.417.26.76.15.5——8.05.996.16.176.225.95.45——9.0——5.135.215.255.34.84.5——10.0——4.354.434.484.524.442.112.0————3.263.323.363.393.411.714.0——————2.492.532.562.581.416.0————————1.91.941.961.218.0——————————1.451.47120.0————————————1.080.8822.0————————————0.760.7524.0——————————————0.6327.0——————————————0.525吨汽车起重机起重性能表（主臂）以下工况仅供参考，实际请与本公司业务员联系！工作半径(m)吊臂长度(m)10.213.7517.320.8524.427.9531.532517.53.520.617.512.29.541817.512.29.54.516.315.312.29.57.5514.514.412.29.57.55.513.513.212.29.57.57612.312.211.39.27.575.16.511.21110.58.87.575.1710.2109.88.57.275.17.59.49.29.18.16.86.75.188.68.48.47.86.66.45.18.587.97.87.46.37.2597.276.866.14.81065.85.65.65.34.41244.14.14.23.93.7142.933.12.93162.22.32.22.3181.61.81.71.7201.31.31.32210.91240.70.8260.50.5280.4290.330(注:本表内红字及红字以上栏目的数字为吊臂强度所决定,其下面栏目数字为倾翻力矩决定)25吨汽车起重机起重性能表（副臂）主臂主角7.5副臂副臂倾角5度副臂倾角30度80度2.51.2575度2.51.2570度2.051.1565度1.751.160度1.551.0555度1.31.050度1.050.830吨汽车起重机性能表（一）以下工况仅供参考，实际请与本公司业务员联系！主要技术参数主臂起重性能工作半径（m）支腿全伸不用支腿名称参数10.00m17.00m24.00m31.00m10.00m全车总重32.2t3.0030.0020.008.00最大爬坡能力31%3.3530.0020.007.00最大提升高度34.00m3.5028.1020.006.40吊臂全伸时长度31.00m4.0024.2020.005.10吊臂全缩时长度10.00m4.5021.4020.0013.004.20最小转弯半径11.50m4.820.0020.0013.003.70最大仰角80°5.019.2019.2013.003.4030t吊钩重0.35t5.517.5017.5013.002.8012t吊钩重0.20t6.016.0016.0013.002.304t吊钩重0.10t6.514.6014.6013.009.001.9010m吊臂时钢丝绳数8根7.013.5013.5012.009.001.6010-17m时钢丝绳数5根7.512.0012.0011.209.001.3024m时钢丝绳数4根8.010.5010.5010.509.001.0031m时钢丝绳数3根8.59.409.409.009.87.207.207.7010.06.956.957.5011.05.805.806.4012.04.904.905.5514.03.453.454.2016.02.503.2018.01.802.4520.01.301.9022.00.851.5024.01.1026.00.7527.00.65(注:本表内红字及红字以上栏目的数字为吊臂强度所决定,其下面栏目数字为倾翻力矩决定)30吨汽车起重机性能表（二）吊臂角度工作半径使用8.45m副臂倾角5°吊臂角度工作半径使用13.5m副臂倾角5°80°7.94.0080°9.32.5078.5°9.54.0077°12.02.5078°10.23.8076°12.72.3576°11.23.3074°14.12.1074°12.22.9072°15.61.9572°13.42.7070°17.11.8070°14.62.5068°18.51.6568°16.02.3566°19.91.5066°17.32.2064°21.31.4064°18.52.1062°22.71.3062°19.82.0560°24.01.2060°20.71.8558°25.31.1558°21.91.6555°27.11.0555°23.61.3054°27.70.9554°24.11.1552°28.80.8052°25.00.9550°29.90.6550°25.80.7548°30.90.5548°26.80.60注：1、若副臂在工作位置，但仍用主臂吊装，主臂的起重性能应相应的减去1.4t2、使用副臂吊装时，主臂的角度不得大于45，否则将倾翻50吨汽车起重机性能表（主表）以下工况仅供参考，实际请与本公司业务员联系！不支第五支腿，吊臂位于起重机前方或后方；支起第五支腿，吊臂位于侧方、后方、前方工作半径(m)主臂长度(m)10.7018.0025.4032.7540.103.050.003.543.004.038.004.534.005.030.0024.705.528.0023.506.024.0022.201...