加工节拍清单

刀具刃数刀具直径编号名称代号Zm m铣6平面(1)铣6平面盘铣刀6275(2)倒角12-1x45°铣刀12710前侧面钻孔、攻丝、倒角(1)6-钻中心孔中心钻626(2)钻2-φ 2孔深1铣刀222(3)钻2-φ 6孔深30麻花钻226(4)钻2-φ 2.05孔深10麻花钻222.05(5)铣66x9.5深1铣刀224(6)攻2-M2.5 螺孔,深6丝攻222.5(7)倒角6-M2.5螺孔φ 2、φ 6、圆孔 0.25x45°麻花钻6210后侧面钻孔、攻丝、倒角(1)4-钻中心孔中心钻426(2)钻4-φ 2.5孔深9麻花钻422.5(3)攻4-M3 螺孔,深6丝攻423(4)倒角4-M3螺孔 0.25x45°麻花钻4210铣底平面钻孔和倒角(1)铣43x30x10铣刀20425(2)铣左29x6.5x5.5槽铣刀245(3)铣右29x6.5x2.5槽铣刀245(4)钻中心孔中心钻126(5)钻φ 2.05孔深11.5麻花钻122.05(6)攻M2.5 螺孔,深11.5丝攻122.5(7)倒角M2.5螺孔0.25x45°麻花钻1710铣左平面、钻孔、攻丝、倒角(1)铣30x9.5x9.5铣刀19210(2)钻中心孔中心钻126(3)钻φ 2.5孔深11麻花钻122.5工序号工 序 内 容刀具OP40OP50工步内容刀具加工次数OP30OP10OP20(4)攻M3 螺孔,深8丝攻123(5)倒角M3螺孔0.25x45°麻花钻1710铣右平面、钻孔、攻丝、倒角(1)铣30x9.5x9.5铣刀19210(2)3-钻中心孔中心钻326(3)钻3-φ 2.05孔深13麻花钻322.5(4)攻3-M2.5 螺孔,深13丝攻322.5(5)倒角3-M2.5螺孔0.25x45°麻花钻1710OP60刀具号线速V主轴转速N每刃进给量/刃每转进给 Fr每分钟进给F切削长度切削时间 每小时NOm/min r/min mm/tip mm/rev mm/min mmsecsecsecsecsecsec30012740.240.486118248.3126.031584.3 0.02315477.70.080.5626812.7216.031547.7 0.01310053080.080.1684920.8126.031536.8 0.0103860510.501.00605110.066.031530.0 0.0083820170.501.002017301.866.031531.8 0.0093859030.501.005903100.266.031530.2 0.0083830250.501.00302510.066.031530.0 0.0083.8484.10.501.0048461.566.031531.5 0.00915477.70.080.16760.251.2126.031537.2 0.0103015920.080.1625521.996.031534.9 0.0101519110.501.00191191.196.031534.1 0.0093.8403.40.501.0040363.696.031536.6 0.01015477.70.080.16760.250.896.031533.8 0.00912015290.502.003057103.9336.031560.9 0.0172012740.502.002548291.466.031531.4 0.0092012740.502.002548291.466.031531.4 0.0093015920.080.1625520.54.56.031529.0 0.0081015540.501.00155411.50.44.56.031528.9 0.0083.2407.60.501.0040811.51.74.56.031530.2 0.0085015920...