光滑极限量规公差VIP免费

光滑极限孔用量规公差表公差等级IT6IT7IT8IT9基本尺寸零件公差数值量规公差带零件公差数值量规公差带零件公差数值量规公差带零件公差数值量规公差带WT、Z极限偏差WT、Z极限偏差WT、Z极限偏差WT、Z极限偏差大于至大于至大于至大于至大于至—30.0050.0080.00150-0.0010.0080.0120.00220-0.00120.0120.0180.00280-0.00160.0180.0300.0040-0.0020360.0060.0090.0020-0.00120.0090.0150.00270-0.00140.0150.0220.00360-0.00200.0220.0360.00520-0.00246100.0080.0110.00230-0.00140.0110.0180.003300.00180.0180.0270.00440-0.00240.0270.0430.00640-0.002810180.0090.0130.00280-0.00160.0130.0210.00380-0.00200.0210.0330.00540-0.00280.0330.0520.00770-0.003418300.0110.0160.00340-0.0020.0160.0250.00460-0.00240.0250.0390.00670-0.00340.0390.0620.00900-0.004030500.0130.0190.0040-0.00240.0190.0300.00550-0.00300.0300.0460.00800-0.00400.0460.0740.01050-0.005050800.0150.0220.00480-0.00280.0220.0350.00640-0.00360.0350.0540.00930-0.00460.0540.0870.01200-0.0060801200.0180.0250.00540-0.00320.00250.0400.00750-0.00420.0400.0630.01070-0.00540.0630.1000.01350-0.00701201800.0200.0290.00630-0.00380.00290.0460.00840-0.00480.0460.0720.0120-0.00600.0720.1150.01600-0.00801802500.0230.0320.00720-0.00440.0320.0520.00970-0.00540.0520.0810.01350-0.00700.0810.1300.01850-0.00902503150.0250.0360.0080-0.00480.0360.0570.0110-0.00600.0570.0890.01600-0.00800.0890.1400.02100-0.01003154000.0270.0400.008900.0400.0630.012500.0630.0970.016500.0970.1550.023501-0.0059-0.007-0.0090-0.01104005000.0300.0440.0100-0.00600.0440.0700.0140-0.00800.0700.1100.01900.01000.1100.1750.02600-0.01202光滑极限孔用量规公差表（续表）公差等级IT10IT11IT12IT13基本尺寸零件公差数值量规公差带零件公差数值量规公差带零件公差数值量规公差带零件公差数值量规公差带WT、Z极限偏差WT、Z极限偏差WT、Z极限偏差WT、Z极限偏差大于至大于至大于至大于至大于至—30.0300.0480.00520-0.00240.0480.0750.00750-0.0030.0750.1200.0110-0.0040.1200.1800.0170-0.006360.0360.0580.00650-0.00300.0580.0900.0100-0.0040.0900.1500.01350-0.0050.1500.2200.01950-0.0076100.0430.0700.00780-0.00360.0700.1100.01150-0.0050.0110.1800.0160-0.0060.1800.2700.0240-0.00810180.0520.0840.01000-0.00400.0840.1300.01400-0.0060.1300.2100.01850-0.0070.2100.3300.0290-0.01018300.0620.1000.01150-0.00500.1000.1600.01650-0.0070.1600.2500.0220-0.0080.2500.3900.0340-0.01230500.0740.1200.01400-0.00600.1200.1900.0200-0.0080.1900.3000.0270-0.0100.3000.4600.0410-0.01450800.0870.1400.01650-0.00700.1400.2200.02350-0.0090.2200.3500.0320-0.0120.3500.5400.0480-0.016801200.1000.1600.01900-0.00800.1600.2500.0270-0.0100.2500.0400.0370-0.0140.4000.6300.0560-0.0201201800.1150.1850.02250-0.00900.1850.2900.0310-0.0120.2900.4600.0430-0.0160.4600.7200.0630-0.0221802500.1300.2100.0250-0.01000.2100.3200.0360-0.0140.3200.5200.0490-0.0180.5200.8100.0730-0.0262503150.1400.2300.02800-0.01200.2300.3600.0400-0.0160.3600.5700.0550-0.0200.5700.89000.0800-0.0283154000.1550.2500.032000.2500.4000.04500.4000.6300.06100.6300.9700.09003-0.0140-0.018-0.022-0.0324005000.1750.2800.0360-0.01600.2800.4400.0500-0.0200.4400.7000.0670-0.0240.7001.1000.0980-0.036光滑极限孔用量规公差表（续表）公差等级IT14IT15IT16注：量规通端（T）的磨损极限位置为被测零件的最小极限尺寸基本尺寸零件公差数值量规公差带零件公差数值量规公差带零件公差数值量规公差带WT、Z极限偏差WT、Z极限偏差WT、Z极限偏差大于至大于至大于至大于至—30.1800.3000.02450-0.0090.3000.4800.0370-0.0140.4800.7500.0500-0.020360.2200.3600.03050-0.0110.3600....