,各吨位吊车起重参数VIP免费

吊车吨位参数表起重臂长度，作业半径与允许起重量对照表（机型QUY35、35t）起重臂长度（m）10作业半径（m）允许起重量（t）3.03.53.63.74.04.55.06.07.08.09.013161922252831允许起重量（t）允许起重量（t）允许起重量（t）允许起重量（t）允许起重量（t）允许起重量（t）允许起重量（t）28.0028.0028.0026.7623.4819.4416.612.7610.368.687.4428.0026.6823.4019.4016.5212.7210.288.607.366.445.0819.3616.4812.6410.168.527.286.365.004.1216.4012.610.168.487.246.324.964.043.4012.5610.128.447.206.244.884.003.322.842.4410.088.407.166.204.843.923.282.762.362.0810.008.327.086.124.763.843.202.682.282.001.728.287.046.084.723.803.162.642.241.921.681.4810.012.013.016.018.020.022.024.026.0注明：1、由于机械磨损，性能降低，起重能力不能达到理论荷载，因此乘以一个折旧系数0.80得到允许起重量。2、起重臂长度即为扒杆长度。3、起重指挥人员不熟悉指挥信号、机械性能、起重臂长度与作业半径、起重量对照表不准上岗。不得发出错误信号。4（机型SCC508、50t）起重臂长度（m）作业半径（m）3.744.555.567891012131619222528313437允许起重允许起重允许起重允许起重允许起重允许起重允许起重允许起重允许起重量（t）量（t）量（t）量（t）量（t）量（t）量（t）量（t）量（t）45.041.435.229.525.422.217.814.812.610.98.635.129.425.322.217.714.712.510.98.67.029.325.222.117.614.612.410.68.46.85.825.122.017.614.512.310.78.36.85.74.821.917.514.412.210.68.36.75.64.74.13.517.414.312.210.58.16.65.54.64.03.43.017.314.212.110.48.06.55.44.53.93.32.92.514.112.010.37.96.45.34.43.83.22.82.42.11.811.910.27.86.45.24.33.73.12.72.32.01.714161820222426283032注明：1、由于机械磨损，性能降低，起重能力不能达到理论荷载，因此乘以一个折旧系数0.90得到允许起重量。2、起重臂长度即为扒杆长度。3、起重指挥人员不熟悉指挥信号、机械性能、起重臂长度与作业半径、起重量对照表不准上岗。不得发出错误信号。严禁超过允许起重量作业（超载作业）。4、作业半径即为吊机底座转盘中心到吊物的水平距离。（机型神钢335、35t）起重臂长度（m）作业半9.14径（m）允许起重量（t）12.915.2418.2921.3424.3827.4830.48允许起重量（t）允许起重量（t）允许起重量（t）允许起重量（t）允许起重量（t）允许起重量（t）允许起重量（t）3.03.23.54.04.55.06.07.08.09.029.7529.7526.3521.9418.1715..5011.949.698.116.9426.9221.8718.1015.4211.879.618.036.905.9821.7918.0215.3411.809.547.966.785.904.653.8017.9415.2711.719.467.876.705.824.573.723.1115.1911.639.387.806.635.664.503.643.032.5511.569.307.736.555.664.423.512.952.482.1211.489.237.656.485.594.343.492.882.412.051.399.157.576.405.514.273.412.802.321.971.3210.012.04.7314.016.018.020.02.2025.0注明：1、由于机械磨损，性能降低，起重能力不能达到理论荷载，因此乘以一个折旧系数0.85得到允许起重量。2、起重臂长度即为扒杆长度。3、起重指挥人员不熟悉指挥信号、机械性能、起重臂长度与作业半径、起重量对照表不准上岗。不得发出错误信号。严禁超过允许起重量作业（超载作业）。4、作业半径即为吊机底座转盘中心到吊物的水平距离。（机型神钢440、40t）作业半径（m）3.54.04.55.06.07.08.09.010.012.0起重臂长度（m）12.915.2418.2921.3424.3827.4330.4833.53允许起重量（t）允许起重量（t）允许起重量（t）允许起重量（t）允许起重量（t）允许起重量（t）允许起重量（t）允许起重量（t）34.0026.9522.1018.7914.3711.569.698.257.235.7026.8622.0218.714.2811.489.618.167.145.614.9523.2818.6214.2011.399.528.087.065.534.513.8318.5314.1111.319.447.996.975.444.423.703.1214.0311.229.357.916.895.364.343.613.032.6013.9411.149.277.826.805.274.273.532.952.521.7511.059.187.746.725.194.173.442.862.431.679.107.656.635.104.083.362.782.351.581.0814.016.018.020.02.6925.030....