27种工程施工机械安全技术操作规程VIP免费

27种工程施工机械安全技术操作规程目录一、土石方机械1、装载机安全技术操作规程····························？二、动力机械1、发电机安全技术操作规程····························？2、锅炉安全技术操作规程·····························？三、起重机械·1、起重安全操作规程·······························？2、塔式起重机安全技术操作规程··························？3、汽车起重机安全技术操作规程··························？4、龙门起重机安全技术操作规程··························？5、叉车安全技术操作规程·····························？6、卷扬机安全技术操作规程····························？四、砼及砂浆机械1、混凝土搅拌机安全技术操作规程·························？2、混凝土搅拌站安全技术操作规程························？3、砂浆搅拌机安全技术操作规程··························？4、张拉安全操作规程·······························？五、焊接机械1、电焊机安全技术操作规程····························？2、气焊安全技术操作规程·····························？3、对焊机安全技术操作规程······························？六、加工机械1、车床安全技术操作规程·······························？2、刨床安全技术操作规程·······························？3、钻床安全技术操作规程·······························？4、空气锤安全技术操作规程······························？5、钢筋切断机安全技术操作规程··························？6、钢筋弯曲机安全技术操作规程··························？七、其他1、支拆模安全操作规程······························？2、配电室安全技术操作规程······························？3、现场施工用电安全技术操作规程·························？4、手持电动工具安全技术操作规程·························？5、电动砂轮机安全技术操作规程···························？装载机安全技术操作规程（1）装载机行驶时，应收回铲斗，铲斗离地约400～500mm。在行驶过程中注意是否有路障或高压线等。除规定的驾驶人员外，不准搭乘其它人员。（2）装载机行驶时，避免突然换向行驶，铲斗带负荷升起行驶时，不准急转弯和急刹车。（3）装载机在公路上行驶时必须遵守交通规则，谨慎驾驶，下坡禁止空档溜放。（4）在倾斜坡地若发动机熄火，应把铲斗放在地上并制动，将各操作杆置于中位，再启动发动机。（5）装载机应注意斗杆不应升太高。（6）对边坡、壕沟、凹坑卸料时，注意不要使铲斗过于伸出，以免倾覆。（7）不得在倾斜度超过规定的场地上工作，作业区内不得有障碍物及无关人员。（8）装载机转向架未锁闭时，严禁站在前后车架之间检修保养。（9）大臂升起后，在进行润滑和调整等工作前，必须装好安全销或采取其它措施支住大臂，以防大臂落下伤人。（10）作业后，应将装载机停放在安全场地，将铲斗平放地面，所有操作杆置于中位，并制动锁定。发电机安全技术操作规程（1）启动前应检查燃油箱油量是否充足，各油管及接头处无漏油现象；冷却系统水量是否充足、清洁、无渗漏，风扇皮带松紧是否合...