电脑桌面
添加小米粒文库到电脑桌面
安装后可以在桌面快捷访问

乘用车钳盘式制动器的结构设计与建模VIP免费

乘用车钳盘式制动器的结构设计与建模_第1页
1/50
乘用车钳盘式制动器的结构设计与建模_第2页
2/50
乘用车钳盘式制动器的结构设计与建模_第3页
3/50
本 科 毕 业 设 计(论文)乘用车钳盘式制动器的结构设计与建模Structural design and modeling of the passenger caliper disc brakes摘 要 本次毕业设计,是进行汽车钳盘式制动器的结构分析与建模,首先文章的开头介绍了什么是汽车的制动系统,以及汽车制动系统的组成,其中汽车在行驶时和停止时的制动是我们考虑的重点,然后依据制动器的制动形式介绍了电磁式,液力式以及最常用的摩擦式制动器。 在说明完基础知识之后,我重点讨论了所涉及的重点,即摩擦式制动器,摩擦式的制动器可依据摩擦副的种类可分为鼓式,盘式与带式,其中鼓式与盘式运用的最为广泛,而由于盘式制动器的优点多,而且随着生产力水平的提升,以及成本的降低,盘式制动器愈来愈多的运用到汽车的生产之中,而盘式之中又以钳盘式制动器运用的最为广泛,因此本文决定设计钳盘式制动器。在确定了设计的制动器类型之后,查阅车身的各种参数后以及国家标准中对制动系统的要求,对制动器本身的结构尺寸,诸如制动盘的直径与厚度,制动钳,摩擦因数以及制动间隙进行了初步设计。在设计好了之后,对各项指标进行校核,在符合标准所制定的要求后,画出了钳盘式制动器的零件图,并进行三维建模。关键词:盘式制动器;设计方法;三维建模Abstract The graduation project is to carry automobile caliper disc brakes structural analysis and modeling, the first beginning of the article describes what constitutes automotive braking systems, and automotive braking systems, where the traffic and the parking brake is our key consideration, and then based on the brake in the form of electromagnetic brake introduced, and the most common type of hydraulic friction brakes. After instructions in the basics, I focused on the focusing involved, namely friction brakes, friction brakes can be based on the type of friction can be divided into the drum, disc and tape, in which the use of drum and disc the most widely used, and because of the advantages of multi-disc brakes, and with increased productivity levels, as well as lower costs, more and more use of disc brakes...

1、当您付费下载文档后,您只拥有了使用权限,并不意味着购买了版权,文档只能用于自身使用,不得用于其他商业用途(如 [转卖]进行直接盈利或[编辑后售卖]进行间接盈利)。
2、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。
3、如文档内容存在违规,或者侵犯商业秘密、侵犯著作权等,请点击“违规举报”。

碎片内容

乘用车钳盘式制动器的结构设计与建模

确认删除?
VIP
微信客服
  • 扫码咨询
会员Q群
  • 会员专属群点击这里加入QQ群
客服邮箱
回到顶部