各吨位吊车起重参数资料全VIP免费

..吊车吨位参数表起重臂长度，作业半径与允许起重量对照表〔机型QUY35、35t〕起重臂长度〔m〕作业10半径允许起(m)重量〔t〕重量〔t〕重量〔t〕重量〔t〕重量〔t〕重量〔t〕重量〔t〕重量〔t〕3.03.53.63.74.04.55.06.07.08.09.028.0028.0028.0026.7623.4819.4416.612.7610.368.687.4428.0026.6823.4019.4016.5212.7210.288.607.3619.3616.4812.6410.168.527.2816.4012.610.168.487.2412.5610.128.447.2010.088.407.1610.008.327.088.287.04允许起允许起允许起允许起允许起允许起允许起13161922252831..word....10.012.013.016.018.020.022.024.026.0注明：6.445.086.365.004.126.324.964.043.406.244.884.003.322.842.446.204.843.923.282.762.362.086.124.763.843.202.682.282.001.726.084.723.803.162.642.241.921.681.481、由于机械磨损，性能降低，起重能力不能到达理论荷载，因此乘以一个折旧系数0.80得到允许起重量。2、起重臂长度即为扒杆长度。3、起重指挥人员不熟悉指挥信号、机械性能、起重臂长度与作业半径、起重量对照表不准上岗。不得发出错误信号。4、作业半径即为吊机底座转盘中心到吊物的水平距离。起重臂长度，作业半径与允许起重量对照表〔机型SCC508、50t〕..word....起重臂长度〔m〕作业13半径允许起(m)重量〔t〕重量〔t〕重量〔t〕重量〔t〕重量〔t〕重量〔t〕重量〔t〕重量〔t〕重量〔t〕3.744.555.5678910121416182022242645.041.435.229.525.422.217.814.812.610.98.635.129.425.322.217.714.712.510.98.67.029.325.222.117.614.612.410.68.46.85.825.122.017.614.512.310.78.36.85.74.821.917.514.412.210.68.36.75.64.74.13.517.414.312.210.58.16.65.54.64.03.43.017.314.212.110.48.06.55.44.53.93.32.914.112.010.37.96.45.34.43.83.22.811.910.27.86.45.24.33.73.12.7允许起允许起允许起允许起允许起允许起允许起允许起1619222528313437..word....283032注明：2.52.42.11.82.32.01.71、由于机械磨损，性能降低，起重能力不能到达理论荷载，因此乘以一个折旧系数0.90得到允许起重量。2、起重臂长度即为扒杆长度。3、起重指挥人员不熟悉指挥信号、机械性能、起重臂长度与作业半径、起重量对照表不准上岗。不得发出错误信号。严禁超过允许起重量作业〔超载作业〕。4、作业半径即为吊机底座转盘中心到吊物的水平距离。起重臂长度，作业半径与允许起重量对照表〔机型神钢335、35t〕起重臂长度〔m〕作业9.14半径允许起(m)重量〔t〕重量〔t〕重量〔t〕重量〔t〕重量〔t〕重量〔t〕重量〔t〕重量〔t〕3.03.229.7529.75允许起允许起允许起允许起允许起允许起允许起12.915.2418.2921.3424.3827.4830.48..word....3.54.04.55.06.07.08.09.010.012.014.016.018.020.025.0注明：26.3521.9418.1715..5011.949.698.116.9426.9221.8718.1015.4211.879.618.036.905.984.7321.7918.0215.3411.809.547.966.785.904.653.8017.9415.2711.719.467.876.705.824.573.723.1115.1911.639.387.806.635.664.503.643.032.552.2011.569.307.736.555.664.423.512.952.482.1211.489.237.656.485.594.343.492.882.412.051.399.157.576.405.514.273.412.802.321.971.321、由于机械磨损，性能降低，起重能力不能到达理论荷载，因此乘以一个折旧系数0.85得到允许起重量。2、起重臂长度即为扒杆长度。3、起重指挥人员不熟悉指挥信号、机械性能、起重臂长度与作业半径、起重量对照表不准上岗。不得发出错误信号。严禁超过允许起重量作业〔超载作业〕。4、作业半径即为吊机底座转盘中心到吊物的水平距离。..word....起重臂长度，作业半径与允许起重量对照表〔机型神钢440、40t〕起重臂长度〔m〕作业12.9半径允许起(m)重量〔t〕重量〔t〕重量〔t〕重量〔t〕重量〔t〕重量〔t〕重量〔t〕重量〔t〕3.54.04.55.06.07.08.09.010.012.014.016.018.020.025.034.0026.9522.1018.7914.3711.569.698.257.235.7026.8622.0218.714.2811.489.618.167.145.614.9523.2818.6214.2011.399.528.087.065.534.513.8318.5314.1111.319.447.996.975.444.423.703.122.6914.0311.229.357.916.895.364.343.613.032.601...