电脑桌面
添加小米粒文库到电脑桌面
安装后可以在桌面快捷访问

异步电动机毕业论文电磁设计计算电动机毕业论文

异步电动机毕业论文电磁设计计算电动机毕业论文_第1页
1/31
异步电动机毕业论文电磁设计计算电动机毕业论文_第2页
2/31
异步电动机毕业论文电磁设计计算电动机毕业论文_第3页
3/31
异步电动机毕业论文电磁设计计算摘 要本文主要针对 Y2-200L-4 型电机进行了电磁设计和计算。首先基于设计任务书给定的参数并结合相关的技术条件确定了与 Y2-200L-4 电机的电磁性能有关的主要尺寸,选择定、转子的槽数与槽配合,用 CAD 绘制出定、转子的槽型和线圈尺寸图,槽型分布图与绕组分布图。计算出每相串联导体数,串联匝数,槽满率等基本量,然后据此选定有关的材料。再在 MATLAB 中编程进行该电机的电磁计算,反复调整有关参数,使其技术指标符合任务书的要求,最终设计出符合任务书规定技术要求的电机。关键词:Y2-200L-4;定转子;绕组分布;电磁设计计算AbstractThisarticle mainly about electromagneticdesign and calculation of Y2-200L-4 motor. First it determined the main dimensions related to the electromagnetic properties of the Y2-200L-4 motor based on the parameters of dsign task and technical conditions. Then it selected the number of slots of stator and rotor and right slots. I not only used CAD to draw size chart of stator, rotor and coil but also draw distribution of groove and winding. I calculated some basic amount such as the number of conductors in series per phase and slot fill factor. Then I selected the related materials. I have completed the electromagnetic calculations of this motor in MATLAB. Then I adjusted the parameters repeatedly. I did a lot of work to make its technical indicators meet the requirements of the mission statement. In the last I designed the motor that meet the requirements of the mission statement.Key Words: Y2-200L-4, stator and rotor, winding distribution, electromagnetic摘要 0ABSTRACT11 绪论 41.1 工程背景 41.2 设计围 41.3 设计依据 41.4 设计目标 41.5 本文的主要工作 42 三相异步电动机主要参数的确定 52.1 主要尺寸与气隙长度的确定 52.2 定、转子槽形与槽配合的确定 52.2.1 定、转子槽形的选择 52.2.2 定、转子槽形尺寸的确定 62.2.3 槽配合的选取 62.3 绕组型式与节距的选择 62.3.1 绕组型式的选...

1、当您付费下载文档后,您只拥有了使用权限,并不意味着购买了版权,文档只能用于自身使用,不得用于其他商业用途(如 [转卖]进行直接盈利或[编辑后售卖]进行间接盈利)。
2、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。
3、如文档内容存在违规,或者侵犯商业秘密、侵犯著作权等,请点击“违规举报”。

碎片内容

异步电动机毕业论文电磁设计计算电动机毕业论文

确认删除?
VIP
微信客服
  • 扫码咨询
会员Q群
  • 会员专属群点击这里加入QQ群
客服邮箱
回到顶部